27-29G pins for oils?

[hanquin]

i can't recall where, but are some of you actually using 27-29G pins for oils? i know is HOW? now, i'm certainly NOT asking for sources, but it would seem to me that the oil would have to be exceptionally thin for this to happen. this baffles me.

 

[Nabz]

I use 27G regularly for oils, yes it is a pain in the ass to push the oil thru but I limit those shots to 1cc shots and if I have to poke more than a CC ill warm up the syringe in a hot wet towel for a few mins, it definitely helps

 

[b_cornelius]

slowly

 

[hanquin]

guess i'll be giving this a shot. literally. scar tissue's killing me.

 

[little slice]

it's much easier to push gear through a 1/2 cc syringe than a 1 cc syringe




much easier

 

[devenidas]

1 cc syringe and 26 G / 1 inch needle goes so so smoothly and easily

Option 2 :- 27 3/4 G pin goes well with 0.5 cc barrel . can go 1 cc too but little harder to push.

Bigger barrel like 2.5 cc with 27 3/4 is really hard to push even when barrel is heated with hair dryer. So barrel need to be smaller if pins are smaller.

 

[mytreefiddy]

I use 28g without a hitch.... However I'd never DRAW with it.... only PUSH

 

[politicaljunkie]

pull out the plunger and backfill the syringe, then carefully push out all the air out the top....SO much easier.

Also if your oil is made with MCT oil I find it easier to push through smaller pins.

 

[raw33man]

31g .3ml,

I backload it

 

[ferd]

I'm pretty lean. I recently switched from 25x5/8" to 27x1/2. I'll sometimes do subq with 30x1/2.

 

[Pekkerwood]

Not a fan. Heated oil helps a lot. Drawing pins? Heck they are so cheap at Walgreens or Walmart.

I find when I have used smaller gauges, the extra movements of the pin from me forcing the plunger causes more trauma than just taking it like a man with the 18 gauge the Sus preloads came in!

 

[Elvia1023]

I am currently using 40mg tren a, 50mg test c and 40mg mast e every night. That works out at 0.8ml total injected every night. I only brought 30G slin pins over with me so I am using them for uploading and injecting. I have no issues with my current gear. Although the test c is much slower than the rest but I am only dosing it at 0.2ml so no issues there.

 

[johnjuanb1]

i can't recall where, but are some of you actually using 27-29G pins for oils? i know is HOW? now, i'm certainly NOT asking for sources, but it would seem to me that the oil would have to be exceptionally thin for this to happen. this baffles me.

I'm injecting 50mg inject anadrol daily with a 27 gauge slin pin. Flows perfectly!

 

[Dema]

Slow and steady!!! If you have thin oil it's a breeze! The think oil takes some time but less scare tissues when your pinning Ed

 

[Oxford Rep]

I personally use as many others a 29g slin pin and also use the back loading method it works wonders.

 

[IronKong]

My fav is a 28g .5" needle. Draws fine for 200mg/ml oil and no pain. You could go longer if you want but it's preference.

 

[Ashop]

i can't recall where, but are some of you actually using 27-29G pins for oils? i know is HOW? now, i'm certainly NOT asking for sources, but it would seem to me that the oil would have to be exceptionally thin for this to happen. this baffles me.

You have to backload the pin and then some oils will pass.

 

[brazil]

I use 28g without a hitch.... However I'd never DRAW with it.... only PUSH

I have used this as well, I had to draw which took about 2 min for 1cc. Pain free.

 

[tcs439]

how do you go deep enough into the muscle when using a slin pin?

 

[repmks]

how do you go deep enough into the muscle when using a slin pin?

Depends how lean you are. if youre lean .5 will work on any musclegroup. I dont think there is any benefit if your .5 deep into a muscle belly or 1.5 inch deep just more scar tissue. After u massage it a bit most if it is spread throughout the entire muscle anyway.

IF youre lean you can easily tell if the pin is in the muscle or fat. I think the guidline for going 1 to 1.5 is because generally people vary in bodyfat.