any way to fix my cyp?

[cal]

i conveted test cyp according to stickied instructions on anabolex...after a few days it started crystallizing...is there some way i can fix this?

i heated it and it became clear and fluid ...but then crystalized again...i only heated it enough to "melt" the crstals...will more extensive heating fix the problem...

 

[Maverick]

Sounds like you didn't have enougg BA and BB to keep it in the solution. Adding a slight amount of BA and BB to it should help.



Maverick

 

[FRKNHUGE]

i had a conv that crashed and all i did was when i wanted to hit some, i dropped the bttl in hot water for a few mins, shook it, and drew it out and inj it
frk

 

[cal]

FRKHUGE,

does that in anyway weaken the potency of the solution?

 

[zephyr22]

I doubt it....

I have done the same thing. Warmed it in the hot water in the sink. I saw no problems always worked well for me. Yeah for some reason cyp is kind of weird in that it seems to fall out of solution easy. I like enthenate a little better due to it staying in solution much easier. Later.

 

[bigbaldbulldog]

i had a conv that crashed and all i did was when i wanted to hit some, i dropped the bttl in hot water for a few mins, shook it, and drew it out and inj it
frk

All you really need to do is stick it under hot water for a few minutes when you are ready to shoot and you will set bro... How many mgs per ML is it ??

 

[Kahn]

mg/ml was my question, too. Was it too high and what about the pain if it was high? What about crystalizing once in the body or is the body too warm for that to reoccur?

 

[FRKNHUGE]

my cyp was abt 350mg/ml
and it seems as tho some of u thought i mixed ti with water??? i merely sat the bttl in a glass of hot water, to heat it thru
it doesnt weaken the potency by anymeans
as far as crystalizing in the body i have had no issues
frk

 

[bigbaldbulldog]

my cyp was abt 350mg/ml
and it seems as tho some of u thought i mixed ti with water??? i merely sat the bttl in a glass of hot water, to heat it thru
it doesnt weaken the potency by anymeans
as far as crystalizing in the body i have had no issues
frk

WOW and i thought my 300 mgs was high and awesome..350 mgs twice a week (2ml) sure beats the old days when you had 200 mgs to take and you do 1-2 ml EOD..good job FREAK at 350 mgs...

 

[FRKNHUGE]

it was a custom mix, lol
it looked like jelly when it crashed too
frk

 

[rAJJIN]

1

CAL-
Couple of questions..
what % of ba did you use? also did you use any bb?
What mg did you make it? Im not familiar with anabolex directions but Im sure I can help you save it., Ive had a few batches do the same in the beginning.

where do you store it? if it gets to cold it can crash.

Just heating it will work yes but its not going to hold in the oil
unless you either add more Ba and or BB or oil.

300mg is perfect imo on the cyp for a good strong product with minn pain.

 

[cal]

Rajjin,

I used the formula stickied on Anabolex. It was supposed to make solution 5%

I just added some BA and heated, not baked or anything too extreme, just hot water from sink, and it worked out great. No pain or anything.

Can you someone sticky or post ...formulas, (as high MG as possible without crashing or excess) pain on the basic conversion for basic stuff...

THANKS.

CAL

 

[rAJJIN]

`

So you did get it fixed?

5% on the ba is correct but the trick is the added bb.
12-15% on the cyp along with 5-6% ba will do 300+mg no problems.

I notice a lot of directions and people will use only ba.. the bb helps a LOT
and also makes for a less painfull- thinner injection.

 

[cal]

yes i added a few mls of BA...and heated it...it has stayed in solution just fine, its only 200mg.cc

i will do test enanthate next at 300...i dont mind shooting, i just hating finding new sites, glutes and quads are only safe spots for me...for whatever reason, delts always get really blown up and bruise up a bit...

 

[KaotikChem]

Our super magic can get those high mg/ml ratios WITHOUT all that BA and or BB with no crashing whatsoever even at low temperatures.

400mg/ml Test Propionate has been acomplsihed with it using about 1ml per gram of powder.