I think pretty much all the orals will dissolve in everclear. Put some flavoring oil in there like "coconut" and put them in a dropper bottle. They'll still taste like crap.
Some use peg and some heat. Peg tastes a little better but I don't know what the recipe is.
I've used retired "research chem" droppers or liquid baby tylenol dropper vials will work in a pinch.
Homebrew sure is fun if you ask me. I remember my first conversion. It was Nolvadex 20mg/ml. It was clear as water in 190 proof grain alcohol after some heat. Then two days later it crashed and I felt so let down. I followed the formulas out there and it wasn't working out. So I dug deeper and learned about PEG's and molecular weights and the such. I have made almost every conversion their is in the homebrew realm and would like to share my liquid oral recipes with the anabolic world.
For each hormone I listed ingredients needed. For the procedure scroll down.
Anadrol:
Highest concentration made - 50mg/ml
Per 1 gram of Oxymetholone you will need:
8.4 ml's of PEG 300
10.5 ml's 190 Proof Grain Alcohol
Anavar:
Highest concentration made - 20mg/ml
Per 1 gram of Oxandrolone powder you will need:
9.8 ml's of PEG 300
39.2 ml's of 190 Proof Grain Alcohol
Armidex:
Highest concentration made - 5mg/ml
Per 1 gram of Anastrozole powder you will need:
19.9 ml's PEG 300
179.1 ml's of 190 Proof Grain Alcohol
Clomid:
Highest concentration made - 50mg/ml
Per 1 gram of Clomiphene Citrate you will need:
8.4 ml's of PEG 600
10.5 ml's 190 Proof Grain Alcohol
Dianabol:
Highest concentration made - 50mg/ml
Per 1 gram of Methandrostenolone powder you will need:
19 ml's of 190 Proof Grain Alcohol
No PEG needed. Follow the no PEG recipe.
Femara:
Highest concentration made - 5mg/ml
Per 1 gram of Letrozole powder you will need:
19.9 ml's PEG 300
179.1 ml's of 190 Proof Grain Alcohol
Nolvadex:
Highest concentration made - 20mg/ml
Per 1 gram of Tamoxifen Citrate you will need:
9.8 ml's of PEG 600
39.2 ml's of 190 Proof Grain Alcohol
Proviron:
Highest concentration made - 50mg/ml
Per 1 gram of Mesterolone you will need:
8.4 ml's of PEG 300
10.5 ml's 190 Proof Grain Alcohol
Winstrol:
Highest concentration made - 25 mg/ml
Per 1 gram of Stanzolol you will need:
7.8 ml's of PEG 300
31.2 ml's of 190 Proof Grain Alcohol
Step 1. Prepare a hot water bath. Boil water in microwave or on a pot. Once boiling starts remove from heat.
Step 2. Place PEG and powder in beaker.
Step 3. Place the beaker deep enough in to the water so that the hot water is level with the PEG and powder. Gently swirl or stir with a stir rod until solution is clear. Reheat water as needed.
Step 4. Allow PEG to cool some. Then add in your 190 proof alcohol. You don't have to do this drop by drop but don't just dump it in. Pour it in slowly.
Step 5. Stir or gently shake until mixed.
For recipes that do not require PEG.
1. Mix powder and 190 proof alcohol.
2. Stir with stir rod or shake. Most powders that do not require PEG will disolve no problem. If heat is needed follow the instructions for heating powders that use PEG.
it says per 1gram or 1000mg(thats about equal to 20 tablets of anadrol at 50mg/tab).this formula will give you about 20ml of solution.8.4+10.5+displacment of powder should= 20ml.