CJC1295 w/o DAC and GHRP2 in the same syringe

narenp · Apr 7, 2012

Is it possible to draw GHRP 2 first and then give it a air gap of about 2-3 IU and then draw in CJC and then pin with the same needle i know there is an air gap but i am guessing that 2iu on a 40 iu insulin needle should not be a problem(or i could be wrong) any input on this...

jamescb77 · Apr 7, 2012

draw your mod grf first then your ghrp second. No need to leave an air gap. Inject after drawing.

johnjuanb1 · Apr 7, 2012

jamescb77 said:
draw your mod grf first then your ghrp second. No need to leave an air gap. Inject after drawing.

:yeahthat:

sammy555 · Apr 7, 2012

jamescb77 said:
draw your mod grf first then your ghrp second. No need to leave an air gap. Inject after drawing.

Im assuming he means to take to work or out and about? If that is the case the air bubble normally works but sometimes it merges into 1.

Sent from my GT-I9100 using Tapatalk

maxwkw · Apr 8, 2012

I've used the same syringe always. Maybe I'll try separating and see if its different

klimentiy · Apr 8, 2012

Dat's says it would be good for up to a day if stored correctly.

Otherwise i would draw them in separate pinz

narenp · Apr 8, 2012

Thankyou,
I will be trying it from tomorrow the reason i wanted to give an airgp was that the 2 dont merge but your right sometimes they do cant get it right all the time anyways i am going to pin immediately after drawing them no time to store it but i was a little curious about why mod grf first and then ghrp which means the ghrp goes in first and then the mod grf any pirticular reason for this order as in i have read mod grf is delicate but please elaborate..Thank you

tacoman · Apr 8, 2012

I always like to have separation for each of the mod grf and the ghrp 2, makes measuring easier. When you are ready to pin just hold with needle part pointing up and thrust the needles down, making all the liquid contents mix up. Then push down the syringe until no air and pin.

jamescb77 · Apr 9, 2012

narenp said:
Thankyou,
I will be trying it from tomorrow the reason i wanted to give an airgp was that the 2 dont merge but your right sometimes they do cant get it right all the time anyways i am going to pin immediately after drawing them no time to store it but i was a little curious about why mod grf first and then ghrp which means the ghrp goes in first and then the mod grf any pirticular reason for this order as in i have read mod grf is delicate but please elaborate..Thank you

the reason to draw the mod first is because it is more delicate. If you have a little mod slip into your ghrp2 vial not really a big issue if you have ghrp2 slip into your mod vial it could cause bigger problems. This is why mod first then ghrp.

builtbeast · Apr 10, 2012

I usually put a 3-4 IU gap and it seems to be fine. Right before you're ready to pin pull in some more air and then give the syringe a few flicks and the air bubble will rise to the top and you can expel them. It's water and the surface tension is easy to break so you can eliminate the air gap with ease. This is using 30g .3ml pins though. maybe it's more difficult with a 1ml syringe though I can't imagine that being the case.

narenp · Apr 11, 2012

jamescb77 said:
the reason to draw the mod first is because it is more delicate. If you have a little mod slip into your ghrp2 vial not really a big issue if you have ghrp2 slip into your mod vial it could cause bigger problems. This is why mod first then ghrp.

Thank you that is what i was guessing Thanks a lot for the explanation...

narenp · Apr 11, 2012

builtbeast said:
I usually put a 3-4 IU gap and it seems to be fine. Right before you're ready to pin pull in some more air and then give the syringe a few flicks and the air bubble will rise to the top and you can expel them. It's water and the surface tension is easy to break so you can eliminate the air gap with ease. This is using 30g .3ml pins though. maybe it's more difficult with a 1ml syringe though I can't imagine that being the case.

Yup i am actually using a 31g needle and i tried it having the air gap with about 5 units of an airgap on a 40 unit insulin syringe b/w the mod grf and ghrp and it seems good a little tricky trying to balance the 2 and not let them to mix but well worth the effort so every time i inject i put about 5units of air in i do subq so is that a concern the air thing...