Buy Needles And Syringes With No Prescription
M4B Store Banner
intex
Riptropin Store banner
Generation X Bodybuilding Forum
Buy Needles And Syringes With No Prescription
Buy Needles And Syringes With No Prescription
Mysupps Store Banner
IP Gear Store Banner
PM-Ace-Labs
Ganabol Store Banner
Spend $100 and get bonus needles free at sterile syringes
Professional Muscle Store open now
sunrise2
PHARMAHGH1
kinglab
ganabol2
Professional Muscle Store open now
over 5000 supplements on sale at professional muscle store
azteca
granabolic1
napsgear-210x65
advertise1
over 5000 supplements on sale at professional muscle store
over 5000 supplements on sale at professional muscle store
ashp210
UGFREAK-banner-PM
esquel
YMSGIF210x65-Banner
over 5000 supplements on sale at professional muscle store
over 5000 supplements on sale at professional muscle store
over 5000 supplements on sale at professional muscle store
over 5000 supplements on sale at professional muscle store
over 5000 supplements on sale at professional muscle store
over 5000 supplements on sale at professional muscle store
over 5000 supplements on sale at professional muscle store

Did I just ruin my Tren ???

Beentheredonedat

New member
Registered
Joined
Nov 5, 2013
Messages
42
I bought 100ml of Tren Enanthate that I had to transfer from an unsterile essential oil bottle to a sterile 100ml bottle. I dumped the Tren into a clean measuring cup and transfered it all into the sterile vial. The product comes filtered and has the BA/BB in it obviously but needed transfered for injections purposes. I then baked it at 200 degrees Fahrenheit for 40 min. My question is did I just ruin the hormone. I know you can heat Tren too much and I'm not sure if it was baked before or not. If anyone can chime in on this I'd appreciate it.
 
If you didn't filter and bake the trenbolone, I wouldn't use it. Just to be on the safe side, filter, bake and re-sterilize the container.
 
When I made my own SEO I didn't filter and had no problems just by adding BA. My question is, did I just bake off all the hormone
 
A few questions:

Why not just run it through a sterile filter into the sterile vial without baking?

Where did you get the 200 degrees from? And the 40 minutes?
 
Last edited:
If it came in a non-sterile container, it needs to be re-filtered into a sterile vial. No need to bake if it's properly made gear.

200 degrees seems a bit high, but your gear should be ok, although I strongly recommend you to re-filter it.

The BA would take care of any bacteria, but impurities from the non-sterile container are still there.
 
Thanks Ya'll. I got all my info on the baking from Google about homebrew. I did order a .22um Whatman filter and a new vial. I'll transfer it into there once again with the filter this time. After I Googled homebrew I started find I ng a lot of info on Tren being sensitive to heat degradation and oxidation possibly damaging the hormone itself. Just want to know I didn't waste hundreds of dollars on this bottle and that it's still gonna produce.
 
Yep.

You may want to add 1% BA in case it all evaporated from the long baking.

Regarding hormone degradation, there's no way to know. You'll have to use it and see how it works.
 
The reason I ask about the filtering and if it's 100% necessary is bc I made and used 5 100ml bottles of homemade SEO that I prepared the same way out of MCT oil last yr. Poured it out of the 1 liter jug straight into a plastic measuring cup, shot it into a sterile 100ml vial, added 3ml of BA, shook, let sit for 24 hrs and used. Never once got an infection out of 5 bottles. That is why I think the filtering again maybe unecessary. Thoughts ?
 
Filters cost pennies. Better safe than sorry. Glad you didn't have a problem.

I did a quick Google search last night before I posted and I am sorry, I have short term memory loss. But I think I remember that the temperature required to damage the hormone was way higher than 200, so you should be gtg there.

If I was doing this for myself, I'd be using sterile filters. Worth the peace of mind, in my opinion.
 
Last edited:
I got the .22 filter and new sterile bottle on the way. Just throwing my experience out there bc others may find it useful.
 
Unfortunately it's Enanthate. I've been looking everywhere and from what I can find the temp shouldn't have been high enough to do damage. Maybe it evaporated some of the BA but I added 2ml back to it today. I'm going to take a nice big shot tomorrow of 500mg to see if a front load will help. Then I plan on pinning 2cc EOD until all 100ml is gone.
 

Staff online

  • Big A
    IFBB PRO/NPC JUDGE/Administrator

Forum statistics

Total page views
558,010,554
Threads
135,749
Messages
2,768,449
Members
160,339
Latest member
Dann828
NapsGear
HGH Power Store email banner
your-raws
Prowrist straps store banner
infinity
FLASHING-BOTTOM-BANNER-210x131
raws
Savage Labs Store email
Syntherol Site Enhancing Oil Synthol
aqpharma
yourmuscleshop210x131
hulabs
ezgif-com-resize-2-1
MA Research Chem store banner
MA Supps Store Banner
volartek
Keytech banner
musclechem
Godbullraw-bottom-banner
Injection Instructions for beginners
Knight Labs store email banner
3
ashp131
YMS-210x131-V02
Back
Top