Buy Needles And Syringes With No Prescription
M4B Store Banner
intex
Riptropin Store banner
Generation X Bodybuilding Forum
Buy Needles And Syringes With No Prescription
Buy Needles And Syringes With No Prescription
Mysupps Store Banner
IP Gear Store Banner
PM-Ace-Labs
Ganabol Store Banner
Spend $100 and get bonus needles free at sterile syringes
Professional Muscle Store open now
sunrise2
PHARMAHGH1
kinglab
ganabol2
Professional Muscle Store open now
over 5000 supplements on sale at professional muscle store
azteca
granabolic1
napsgear-210x65
advertise1
over 5000 supplements on sale at professional muscle store
over 5000 supplements on sale at professional muscle store
ashp210
UGFREAK-banner-PM
esquel
YMSGIF210x65-Banner
over 5000 supplements on sale at professional muscle store
over 5000 supplements on sale at professional muscle store
over 5000 supplements on sale at professional muscle store
over 5000 supplements on sale at professional muscle store
over 5000 supplements on sale at professional muscle store
over 5000 supplements on sale at professional muscle store
over 5000 supplements on sale at professional muscle store

too small pin?

letz

Member
Registered
Joined
Jun 24, 2011
Messages
375
So, ive been using 5/8" for site injecting in my bicep and thought same would work good for either bicep or delt area, but im wondering if the pin is too thin, i had problem getting the parabolan into the syringe, and it was really hard to get the oil out, almost even couldnt aspirate, or it could be the syringe
 
I've done hundreds of half inch pins into delts and bis, that's a fine length, try warming your oil to improve viscosity

Sent from my SCH-I500 using Tapatalk
 
I've done hundreds of half inch pins into delts and bis, that's a fine length, try warming your oil to improve viscosity

Sent from my SCH-I500 using Tapatalk

alrighty:) thanks for the tip
 
ya cus that wud explain alot if hes using a slin pin of course u wud have a hard time pulling the oil into it...if it is a slin pin u need to backload it super easy
 
ok 25's do suck to pull with if u can get ur hands on some 18 gauge tips and use them just to suck out the oil into the syringe and then change the tip back to the 25 it keeps the 25 tip sharper for when u actually inject and it also makes it easy as hell to suck out ur gear
 
ok 25's do suck to pull with if u can get ur hands on some 18 gauge tips and use them just to suck out the oil into the syringe and then change the tip back to the 25 it keeps the 25 tip sharper for when u actually inject and it also makes it easy as hell to suck out ur gear

well the problem wasnt really getting it into the syringe, it was rather getting it out once it was in my muscle, and aspirating, kinda felt like a damn hard vacum when i tried to aspirate, would just barely move back, guess the oil is thick so ill try warming it
 
well the problem wasnt really getting it into the syringe, it was rather getting it out once it was in my muscle, and aspirating, kinda felt like a damn hard vacum when i tried to aspirate, would just barely move back, guess the oil is thick so ill try warming it


Should always feel like a hard vacuum when aspirating, since there's nothing to pull into the syringe if you're not in a vein. That vacuum you feel means you're in a good spot.
 
ya cus that wud explain alot if hes using a slin pin of course u wud have a hard time pulling the oil into it...if it is a slin pin u need to backload it super easy

I dont backload, i suspend vial upside down, insert slin pin(29 g i think) pull back plunger and come back 5 mins later to full slin pin

Sent from my GT-I9100 using Tapatalk
 
^ this is an option but it takes me like 30 seconds to pull out a cc with an 18 gauge and then back load it into a slin pin
 
^ this is an option but it takes me like 30 seconds to pull out a cc with an 18 gauge and then back load it into a slin pin

O yea quicker, i don't spend a penny that i don't have to though, so extra pins not an option, and the tiny bit of oil wasted each time adds up. Just the English in me, we don't like spending money or wasting shit.

Sent from my GT-I9100 using Tapatalk
 
O yea quicker, i don't spend a penny that i don't have to though, so extra pins not an option, and the tiny bit of oil wasted each time adds up. Just the English in me, we don't like spending money or wasting shit.

Sent from my GT-I9100 using Tapatalk

Exact same here. I'm just now going the slin pin route tho. What's the best way you guys found on warming an what temps?
 
Exact same here. I'm just now going the slin pin route tho. What's the best way you guys found on warming an what temps?

Ive never warmed oil in my life, push hard enough and the shit comes out. Easier to push out a slin pin than a 25g due to the increased specific pressure because of the small diameter of barrel. Higher psi

Sent from my GT-I9100 using Tapatalk
 

Forum statistics

Total page views
558,024,288
Threads
135,751
Messages
2,768,519
Members
160,339
Latest member
Dann828
NapsGear
HGH Power Store email banner
your-raws
Prowrist straps store banner
infinity
FLASHING-BOTTOM-BANNER-210x131
raws
Savage Labs Store email
Syntherol Site Enhancing Oil Synthol
aqpharma
yourmuscleshop210x131
hulabs
ezgif-com-resize-2-1
MA Research Chem store banner
MA Supps Store Banner
volartek
Keytech banner
musclechem
Godbullraw-bottom-banner
Injection Instructions for beginners
Knight Labs store email banner
3
ashp131
YMS-210x131-V02
Back
Top