Slin pin for ED use

[biggTdogg]

How do you guys feel about using a 29g 1/2inch slin pin for ED injections of short esters?
I have a couple buddies who swear by them for prop and say they've never had any problems at all!
I'd be doing this during the last 6 weeks or so leading to a show, so I'll be very lean. Right now I use 25 1inch but, the 29's sound real nice for ED use.

Thoughts, comments?

 

[dece870717]

Lol I think your friends are fucking with you. Cause the oil used in roids is way too thick to go through a 29g needle. If you had water based Test Suspension or Winstrol you could pull it off but other that no.

 

[kscowboy]

I use 25g for my prop and its takes a little bit to push it through. A slin pin would take all day to push prop through. Just get some 25g pins.

 

[Krom]

I've used a 29g for ED injections of all sorts of AAS. It works fine for me but just takes some time to load.

 

[Jrizzle385]

Backload the syringe with oil, don't try to draw it up through the tiny 29g needle tip.

There are two issues, one being that it makes injections very slow (Actually a good thing, causes less stress at the depot site), and the other being the short length of the needle. It's difficult to bury it deep enough into the muscle in most cases. If you have reasonable low BF, you can get away with it in a number of smaller bodyparts. I've done it in the past just to take a break from constantly jabbing myself with large guage needles.

 

[norm1220]

If you make your own gear with Ethyl Oleate for at least 50% of the carrier, then using insulin pins is no problem as long as you backload them. This results in a lot less scar tissue when using short esters.

 

[gear-unit]

never had problems with slin pins and as oil.
i think it is good

 

[mike913]

I just started using slin pins (29ga 1") for my prop injections and they work great. AND YES THE PROP CAN BE DRAWN INTO THE SYRINGE THE NORMAL WAY...the only is that you obviously cant switch out the pin like normal, but it doesn't seem to matter much. I should add though, not all oils can be drawn into slin pins.

 

[kal el]

Syntherol past very good with a slin pin.effortles

 

[biggTdogg]

I didn't know they made 29's in 1 inch. I've used 29's before several times, loaded just fine.

 

[nukeM]

How do you guys feel about using a 29g 1/2inch slin pin for ED injections of short esters?
I have a couple buddies who swear by them for prop and say they've never had any problems at all!
I'd be doing this during the last 6 weeks or so leading to a show, so I'll be very lean. Right now I use 25 1inch but, the 29's sound real nice for ED use.

Thoughts, comments?

You can get 27 X 1 which are considerably thinner than 25 gauge.You feel almost nothing sticking 27 gauge.They are Luer Lock so you can draw w/a larger gauge.Personally,I dont think 1/2 pin is deep enough.I've seen & heard too many wondering why they have this bump on their delt that never seems to go away.

 

[minister]

I'd have to say that you would have to be extremely lean to use 1/2" 29 gauge, because if the oil doesn't reach the muscle you may put yourself in danger of an abscess . I tried using the slin pins once years ago, I just didn't have the patience, God bless you guys.

 

[DrEric]

I've been using them for ed use with prop/tren. Based on the 1/2 life you don't have to shoot prop ed, eod is fine. With tren though I'm a believer of ed shots.

Just push the skin flat between your fingers.

 

[sickboy]

I always use a 29G 1/2 slin pin for tren. Totally pain free, delts and tri's only. I'm very lean though and if I go up in bodyfat i switch to a 27g.

 

[biggTdogg]

Maybe I'll see if I can find some 27-1inch. I agree about the prop eod but I wanna do my tren and masteron ed for the last few weeks of my cutter. I've also seen some 25-5/8inch, might try those too.

 

[prime]

Oil just has to reach subq technically. I'd keep the site .5ml or less. If you need to do more than .5ml then pull out at .5ml and finish an inch away from the original site. Draws slow without backloading but injects fine.

But I will say I've never done more than .5ml so you'll have to experiment on where you can inject. too near the naval and I find it gets sore. tops of quads and ab area and I don't feel any pain. I'm refering to subq btw.

 

[hugga39]

sounds too small... might work if u warm the oil up...

 

[concreteguy]

How do you guys feel about using a 29g 1/2inch slin pin for ED injections of short esters?
I have a couple buddies who swear by them for prop and say they've never had any problems at all!
I'd be doing this during the last 6 weeks or so leading to a show, so I'll be very lean. Right now I use 25 1inch but, the 29's sound real nice for ED use.

Thoughts, comments?

Can't fit much gear in a slin pin. If you could then half inch wouldnt get it anyway. I think you should man up. I would be more concerned about putting a lump of oil that close to the surface. I think it would be visable. Ya know in second thought, I think BIGA's SEO protocol has you doing synthol in the calves with a half inch pin so I guess you will be OK. Where are you injecting?

 

[biggTdogg]

I normally use 25g 1inch. Been using those for years with no problems. However, I will be doing everyday injections, 7 days a weeks, of test/tren/masteron leading up to a show to keep my blood levels stable. For twice a week shots I don't really mind a bigger needle, but for ed, size matters after a while.

As far as ML, I've got a blend of test/tren/master so I'll only be doing 1/2 cc everyday. I normally rotate quads/sho/glutes, might also consider tri's and traps for small amounts (<1ml). I would never do less than 1 inch for glutes.

 

[concreteguy]

As far as ML, I've got a blend of test/tren/master so I'll only be doing 1/2 cc everyday. I normally rotate quads/sho/glutes, might also consider tri's and traps for small amounts (<1ml). I would never do less than 1 inch for glutes.

Maybe it's just me, I get a knee jurk reaction to putting gear in a 1/2" deep. That's all. and good look at your show dude!