Syringe for Syntherol injections

[Big A]

Jaee
Junior Member

Registered: Jan 2002
Location:
Posts: 18
Syringe for Syntherol injections
What size syringe does everyone use when using Site Enhancement Oils?

I was thinking of ordering 29g 1/2 inch for my bicep shots. What does everyone think?



Report this post to a moderator | IP: Logged

03-25-2002 12:55 AM



rAJJIN
Senior Member

Registered: Jan 2002
Location: Missouri
Posts: 113
Those ~ell work.
Just takes a wile to draw em up.
I use a 25gx5/8.



Report this post to a moderator | IP: Logged

03-25-2002 01:04 AM



MikeS
Senior Member

Registered: Jan 2002
Location:
Posts: 160
If mixed with gear-25g. If straight SEO, 27g. Use a big pin for easier draw!



Report this post to a moderator | IP: Logged

03-25-2002 01:43 AM



Jaee
Junior Member

Registered: Jan 2002
Location:
Posts: 18
I am just going to be using SEO only. I have 25g to draw with. But they are 1 1/2 inch. Which makes it hard (for me) to hold it steady and aspirate when I am trying to just get 1/2 inch below the surface.


I am thinking 1/2 inch pin will be sufficient. Is this ok?



Report this post to a moderator | IP: Logged

03-25-2002 01:49 AM



FlatLine
Member

Registered: Jan 2002
Location:
Posts: 53
Reply
I would say go no smaller than 1 in. You want to get deep into the muscle. I use 25g/1in everytime.


__________________
What the fuck are you looking at?!


Report this post to a moderator | IP: Logged

03-25-2002 02:35 AM



xcelbeyond
Better than avg BB'er

Registered: Jan 2002
Location: West Coast
Posts: 336
This info applies to "ALL" injections:
Use a 20g or 18g to draw gear with. Suck a little air in syringe then replace the pin with a 25g (of course remove air before you poke). Use a 1" for everywhere (quads, delts, bis. tris) and a 1-1/2" for glutes (unless you're one of those skinny guys w/no arse).

You dull a needle poking through the septum in a vial. So, doing this will give you fresh pin for the poke. It takes a LONG time to draw gear through a 25g pin (very frustrating if you do). The 25g will make you inject SLOWER. You shouldn't be injecting faster than 1cc per minute. The 25g will help injections go slower and will cause less trauma at injection site.

xcelbeyond


__________________
Lift smarter, not more


Report this post to a moderator | IP: Logged

03-25-2002 03:07 AM



CasperMilktoast
Junior Member

Registered: Feb 2002
Location:
Posts: 7
xcellent advice

Casper



Report this post to a moderator | IP: Logged

03-25-2002 03:26 AM



Jethro Tull
Member

Registered: Jan 2002
Location: Montana
Posts: 76
Aaaarrgghh!!! So who is right?
I see here that some guys are saying 1/2 in. pins in the bicep and some others who say that they wouldn't go less than an 1 inch!!! So which is it? Big A, you seem to know....can you give an opinion?....I see on your site inj. bulletin you say 1/2 in. to 1in....which do you think is better? Also....I have been trying to massage away lumps in my outer quads [equipoise test inj.] and although I rub the hell out of it...there is still a small lump. What the heck am I doing incorrectly?



Report this post to a moderator | IP: Logged

03-25-2002 05:21 AM



jstrong20
Member

Registered: Jan 2002
Location:
Posts: 51
syntherol should go deep in the muscle. I use 1'' 25g.



Report this post to a moderator | IP: Logged

03-25-2002 09:00 AM



Big A
IFBB PRO / Moderator

Registered: Oct 2001
Location:
Posts: 428
I recomend BOTH 1" and 1/2". You rotate the sites and the depth of the shots around the bicep/tricep. 1/2" is still a IM inj if you are reasonably lean.

If you still have lumps from injecting anything (save for prop or suspensions), inject slower and massage more.
Prop - that makes some of te nastiest bumps there are. If yo try to get bumps with syntherol you won't get them as bad as with prop.



Report this post to a moderator | IP: Logged

03-25-2002 09:27 AM



td24
Junior Member

Registered: Feb 2002
Location:
Posts: 9
What size pin should I use for my calfs?



Report this post to a moderator | IP: Logged

03-25-2002 07:31 PM



Big A
IFBB PRO / Moderator

Registered: Oct 2001
Location:
Posts: 428

quote:
--------------------------------------------------------------------------------
Originally posted by td24
What size pin should I use for my calfs?
--------------------------------------------------------------------------------



26g 1/2"



Report this post to a moderator | IP: Logged

03-25-2002 08:00 PM



Jethro Tull
Member

Registered: Jan 2002
Location: Montana
Posts: 76
THANKS FOR THE INFO ON THE INJECTIONS!
I'LL GO AND PRACTICE THIS LUMP REDUCTION....HELL, I ALWAYS THOUGHT I INJECTED SLOWLY....I'LL GIVE IT A BETTER TRY. THANKS FOR THE INFO.