D
Deleted member 106824
Guest
I know most of this is very basic and yes I have read it several times but with this type of thing I just want to be very sure about everything. I have done one designer steroid cycle so far for 25 days...good gains but after PCT and then trying to cut I clearly didn't hold the gains for long enough because I'm practically back to where I was before. I will be running a 10 week Test E cycle in 4 weeks starting with a 4 week kick start of superdrol and want to make sure that whatever body fat I end at I'm comfortable with holding it for a long time because cutting any time soon after my cycle ends clearly is not good for me. What I mainly want to double check is everything to do with pinning because I have never done it before:
-I have 50 23g 1" pins
-My body fat is around 15%, I doubt I have more than a little more than 1/2in. of fat or so over the muscle in my glutes so this is where I was planning on pinning most of the time
-I have 250mg/ml Test E and will be injecting 500mg per week with 2 injections of 250mg spread 3-4 days apart
1. clean the injection site and top of the vial with rubbing alcohol
2. Stick syringe/pin into the top of the vial with the syringe plunger portion not pushed down yet
3. Flip the vial over and push the plunger portion of the syringe into the barrel to force air into the vial increasing pressure
4. pull back on the plunger portion to the point where 1ml of the syringe is filled with oil
5. Turn the vial right-side up and pull the syringe out of the vial
6. Find the appropriate part of the glutes, here GLUTES INTRAMUSCULAR INJECTION. INJECTING THE GLUTES, How To Do Injections, Injection Instructions, Injection Methods, Injection Guide, Injection Photos, Injection Pictures
7. Quickly pin the needle into the glutes at a right angle to the skin, so nearly the entire needle is in
8. Slowly pull back on the plunger (aspirate) slightly to ensure you will not be injecting into a vein. If blood comes into the syringe then re-pin. If no blood comes into the syringe then continue
9. Slowly inject the oil
10. When all of the oil is injected pull the syringe out, dispose of it and rub the injection area with rubbing alcohol. I was planning on putting antibiotic cream on there for the sake of it but don't really hear about this being done.
Anything I'm missing? Again I just want to make sure I'm covering everything here.
Thanks!
-I have 50 23g 1" pins
-My body fat is around 15%, I doubt I have more than a little more than 1/2in. of fat or so over the muscle in my glutes so this is where I was planning on pinning most of the time
-I have 250mg/ml Test E and will be injecting 500mg per week with 2 injections of 250mg spread 3-4 days apart
1. clean the injection site and top of the vial with rubbing alcohol
2. Stick syringe/pin into the top of the vial with the syringe plunger portion not pushed down yet
3. Flip the vial over and push the plunger portion of the syringe into the barrel to force air into the vial increasing pressure
4. pull back on the plunger portion to the point where 1ml of the syringe is filled with oil
5. Turn the vial right-side up and pull the syringe out of the vial
6. Find the appropriate part of the glutes, here GLUTES INTRAMUSCULAR INJECTION. INJECTING THE GLUTES, How To Do Injections, Injection Instructions, Injection Methods, Injection Guide, Injection Photos, Injection Pictures
7. Quickly pin the needle into the glutes at a right angle to the skin, so nearly the entire needle is in
8. Slowly pull back on the plunger (aspirate) slightly to ensure you will not be injecting into a vein. If blood comes into the syringe then re-pin. If no blood comes into the syringe then continue
9. Slowly inject the oil
10. When all of the oil is injected pull the syringe out, dispose of it and rub the injection area with rubbing alcohol. I was planning on putting antibiotic cream on there for the sake of it but don't really hear about this being done.
Anything I'm missing? Again I just want to make sure I'm covering everything here.
Thanks!