Fixing crashed gear

[Nate.184]

what do you guys do?
i got a 30ml vial of 200mg/ml test cyp that was crashed. i boiled water and poured it into an insulated coffie cup with the vial inside and let it sit for 10min. shook it up and it seemed g2g. now a few days later its starting to crash again. whats the best method to fix it?

 

[tenny]

you could try to cut it

 

[maldorf]

what do you guys do?
i got a 30ml vial of 200mg/ml test cyp that was crashed. i boiled water and poured it into an insulated coffie cup with the vial inside and let it sit for 10min. shook it up and it seemed g2g. now a few days later its starting to crash again. whats the best method to fix it?

If that did not work I think about the only thing you can do is cut it down with some BB. Benzyl Benzoate (spelling?) That is a solvent and should help it to dissolve. Start with something really low like 2% BB and see where that get you after you heat it up. Adding more oil will not work as well, because you are not increasing the solubility of the test in oil by just adding more oil.

 

[jerry0331]

a whole lot of "thinks" and "shoulds" = trash it and get more, my.02

 

[Ruhlfreak55]

just add more solvent....BB or BA....add VERY small amounts until it starts to hold and stay in solution

 

[maldorf]

just add more solvent....BB or BA....add VERY small amounts until it starts to hold and stay in solution

I would not mess with BA, since you dont really know how much is already in there and if you put too much in, which is easy cause its so strong, it will be a very painful injection for many days.

 

[qwerty_uk]

You could either cut it with another product ideally one thats made with a high amount of EO.

Or you could add BB as already suggested, dont forget to keep track of the volume your adding as it will decrease the mg per ml.

Also could be worth putting it into a container that you can put into a oven and bake for 5-15 minutes at 200f ish I've made stuff that I heated only enough to make it dissolve which crashed after a day or so, but was ok after 10minutes at 200f

 

[Gators]

Does crashed mean fallen out of solution?

 

[Ruhlfreak55]

I would not mess with BA, since you dont really know how much is already in there and if you put too much in, which is easy cause its so strong, it will be a very painful injection for many days.

true...forgot to say that

Does crashed mean fallen out of solution?

yes

 

[mojo jojo]

Putting it in the oven at 200 degrees for about 10-15 minutes has always worked for me. This works as long as the medicine concentration isn't too strong to begin with.

 

[Nate.184]

thanks for the input guys. i will try baking it and see if it holds

 

[NWMUSCLE]

Bro, you most likely could just run it under very hot water in the sink for a bit just before drawing and injecting.
It has worked many time for me
You will keep the mg per ml still the same and it only takes a few minutes.
Cheers

 

[maldorf]

Putting it in the oven at 200 degrees for about 10-15 minutes has always worked for me. This works as long as the medicine concentration isn't too strong to begin with.

Many times that will increase solubility to the point that it goes back into solution again, but wait a few weeks or so and it may crash again.

 

[Ruhlfreak55]

Many times that will increase solubility to the point that it goes back into solution again, but wait a few weeks or so and it may crash again.

I would think it would always crash again.....you've not changed anything chemically....and it was in solution in the beginning...
of course heat will make it go back into solution temporarily

 

[mojo jojo]

Many times that will increase solubility to the point that it goes back into solution again, but wait a few weeks or so and it may crash again.

If the solution was too strong to begin with then heating it will only last temporarily. However if you are currently using the gear then temporarily is all you need.

If the gear happened to get too cold and crashed then heating it can get it to dissolve again. In this case it should not crash again unless it once again gets too cold.

 

[-b-]

bake at 350 degrees for about ten mins, may want to put a needle through the top to let out pressure. hope this helps. has helped me in past with my research materials

 

[maldorf]

I would think it would always crash again.....you've not changed anything chemically....and it was in solution in the beginning...
of course heat will make it go back into solution temporarily

Yes. Somtimes though you hear about guys exposing their brew to cold temperatures or something freak like that. Other than that, yeah its always going to go back to the same state.

 

[maldorf]

If the solution was too strong to begin with then heating it will only last temporarily. However if you are currently using the gear then temporarily is all you need.

If the gear happened to get too cold and crashed then heating it can get it to dissolve again. In this case it should not crash again unless it once again gets too cold.

Yes. It is a good temp fix but a pain in the ass if you have to go through all of that trouble to heat it up each time you inject. Oh, and if you do, dont forget to let it cool down before you inject it,LOL!

 

[Ruhlfreak55]

Yes. Somtimes though you hear about guys exposing their brew to cold temperatures or something freak like that. Other than that, yeah its always going to go back to the same state.

true

 

[cromespider]

oven 190 degrees for 20 min and then leave in oven and let cool off for about another 20 works every time