baking temp for gear?

[Ragin' Cajun]

I know the temp for Test E is 250 deg.
what's the temp for EQ?

 

[EDED]

baking for what

sterility? i hope not


homebrewing 200-250 works fine, someone has pushed it to 300F with no problem

and thats for all, including hard to dissolve orals

 

[Tough Old Man]

I know the temp for Test E is 250 deg.
what's the temp for EQ?

There is no need to bake the gear..I have been brewing for over 10 yrs and never bake it

 

[CanadianMuscle]

I bake before I add any hormone. will go to 250 to kill off anything possibly in there. Take it out, let it cool for a bit, mix in the hormone while still hot to help things dissolve. Add my BB/BA then as well. Then it's all through a filter.

sterilize the vial while that's going on. Fill and Enjoy!

 

[njpooldude]

baking for what

sterility? i hope not


homebrewing 200-250 works fine, someone has pushed it to 300F with no problem

and thats for all, including hard to dissolve orals

why do you hope not? Big Bapper once told me he always baked his gear to sterilize it. Or he would use a pressure cooker.. It wasnt home brew either..
It was a trsuted sponsor, he just wanted to be extra careful...
rip man

 

[bigindian]

It's probably redundant due to the alcohol.

 

[whome]

i heat to 180-200 add ba bb then let cool to 160 add hormone mix the hell out of it when fully dissolved fitler it done no problems EVER with this method ba sterilizes this shit out of it as well as filtering it if you are not satisfied add more ba but more ba means more pain thats why some UG labs have painful shit cause they do not make it under sterile conditions so add ba

 

[h8tr3d]

There is no need to bake the gear..I have been brewing for over 10 yrs and never bake it

i agree brother

 

[T TOTAL]

why do you hope not? Big Bapper once told me he always baked his gear to sterilize it. Or he would use a pressure cooker.. It wasnt home brew either..
It was a trsuted sponsor, he just wanted to be extra careful...
rip man

I may have to do this as i have some from a trusted and touted sponsor and recieved abscess on the 2 occasions i ' tried ' there product!!!!!

Is it a sterility issue or is it an allergy as it was the 1st time i had tried there stuff

 

[morphysique]

There is no need to bake the gear..I have been brewing for over 10 yrs and never bake it

natural is best

 

[Nssca]

why do you hope not? Big Bapper once told me he always baked his gear to sterilize it. Or he would use a pressure cooker.. It wasnt home brew either..
It was a trsuted sponsor, he just wanted to be extra careful...
rip man

Baking does nothing. Its an old gimmick IP used to tell people to do cause his gear hurt so much. The BA in the oil wil not let anything grow in the oil.
No Need to bake what so ever. no matter how many dead sponsors say other wise.

 

[V3ng3anc333]

i brew since almost 7 years now and never baked.. i DO heat the solution but only for very short amounts of time to let everything dissolve.
But adding 1%BA and filtering thorug a 0.2 filter is more then enough.

I figure some UG labs dont filter @ all and thats why some guys experience a sterile abscess.

 

[EDED]

trusted or not, mass produced UG labs everywhere who knows what they are doing??

home brew is better,

yeah i would feel sketchy using TRUSTED ug labs whoever it is

heat sterilization sucks, pressure cooker is fine, but how do you pressure cook with a sealed vial, steam needs to go in there

autoclave works like that, in the lab they dont have sealed bottles in there, they have a autoclave tape or aluminum foil on the bottles and ahhhh nevermind, im sure this has been discussed.

i think heat sterilization temp is like 400F for an hour for glassware,,,,find ou what you need to do for a SEALED CAPPED OIL and find out at which point all the chemicals in there get destroyed blah blah, what a headache

just filter it again with 0.22um and pray that there is no smaller bugs in there everytime you shoot lolol


if its for homebrew

200F or 250F heat ba/bb/pwder 15-30 min, swirl, add heated oil, swirl, heat 15-30min

let it cool and watch 48 hours if it crashes or not, then heat it to 200f, let it cool off until you can hold on to the glassware but still very warm then sterile filter into whatever