is enanthate 250 supposed to hurt?

[s.norman]

is enanthate at 250/ml supposed to cause swelling and pain for newbies? and if these newbies do not inject properly will that cause pain and swelling also?
would enanthate at 200/ml be better for newbies to take?
i'm sick and tired of listening to them whine in the gym about how painful it is when i am using the same exact stuff only at 400/ml and i have no pain nor swelling

 

[617ricky]

There's so many variables that go into it.. The brand, what body part they injected in, the spot they injected it in, etc..

 

[alecaf]

the amount of benzyl alcohol, the kind of oil its in are also variables. Maybe its over dosed.

 

[Snooze]

What brand are you using?

 

[jimmyjones]

Im running our chinese friends Test E 300mg/ml at 375mg/week and it is so painless its almost incredible. It is suspended in Ethyl Oleate

The trick to painless injections is to
- Stick the needle in very quickly like a dart,
- Use a smaller size needle, I use a 25G 1.5inch needle, and I warm up the oil beforehand, and although it goes in slowly, it is very smooth. I leave the needle in there for about 5 seconds to make sure all the goodness is in me, and then pull out very quickly. Its painless everytime, and I have no cheek soreness the next day.

 

[jm425]

Im running our chinese friends Test E 300mg/ml at 375mg/week and it is so painless its almost incredible. It is suspended in Ethyl Oleate

The trick to painless injections is to
- Stick the needle in very quickly like a dart,
- Use a smaller size needle, I use a 25G 1.5inch needle, and I warm up the oil beforehand, and although it goes in slowly, it is very smooth. I leave the needle in there for about 5 seconds to make sure all the goodness is in me, and then pull out very quickly. Its painless everytime, and I have no cheek soreness the next day.

You've never done t400 have you or prop? If you did you would know that there is no trick to painless injections. You can cut it with oil, heat it up, etc., but if the hormone volume is too high or if it's a short ester like prop which is known to be acidic, it's going to hurt. Doing those things you suggested from my experience only slightly reduces pain.

 

[617ricky]

That Denkall T400 was no joke!

 

[maldorf]

That Denkall T400 was no joke!

Would cripple a horse!

 

[MR. BMJ]

There should be no reason why a solution of Test Enan @ 250mg/ml should have any pain at all. I'd highly recommend reading Massive G's newest thread on baking gear to alleviate any pain expressed by the solvents. It should still be on the first page here at the site....2nd page at most.

BMJ

 

[s.norman]

There should be no reason why a solution of Test Enan @ 250mg/ml should have any pain at all. I'd highly recommend reading Massive G's newest thread on baking gear to alleviate any pain expressed by the solvents. It should still be on the first page here at the site....2nd page at most.

BMJ

i'm using the same stuff dosed at 400mg/ml w/ no problems in ethyl oleate...actually i hear people complaining about the enanthate dosed at 200mg/ml in ethyl oleate, wtf...they claim they are getting lumps and pain and even going to the hospital...i don't have any problems w/ the enanthate but i'm extremely puzzled as to why some people are having such drastic problems...i know its real i just had my total test=4,850ngs/dl......

 

[njpooldude]

i think it all comes down to the person. ive used stealth test e at 250ml and it crippled me..a buddy of mine was fine with it..

then used HG test e.. no pain at all..

that tread that was posted says u can bake your gear at i THINK 340F for an hour and it will sanitize it and also help with the pain..

also make sure the newbs warm the oil once its in the syringe and ready to un-load. i always run it under HOT water for a min or so, then inject..helps alot