OUCH!

[SouthernMuscle]

so last monday I started a cycle of test and eq, did 2mls of 400mg/ml test in the right glute and 2mls of 400mg/ml eq in the left. The next day my right glute was so swollen and painful that I could barely walk, and by the third day I pretty much couldn't, but the left side with the eq was perfectly fine. Both were from the same source. So after a week of icing it and eating ibuprofens like crazy, the swelling and pain finally went away but I still have a knot on my right glute. So I figured I must have screwed up the injection and was a lot more careful yesterday when I injected again, this time I switched the test to the left, and once again , swollen and painful as hell, and the right one with the eq is fine. The BA content is pretty low in the test, .02ml/ml, the eq is actually higher with .03

so I'm at a loss here fellas, no idea what's causing this, any ideas?

any help is appreciated

 

[rAJJIN]

well

The problem is there is no reason to make it at such a high mg.. thats whats causing your pain- Not the way you injected it.

imo 300mg on either of the two hormones you mentioned is the limit
Before you get into sore injections..and thats pushing it.
Id never buy a product that was 400mg per ml.

 

[TooPowerful4u]

agree with rajjin. Didnt you hear about the pain factor people were complaining about with the 500mg/ml test they were making a while back. Hurt so bad nobody wanted to use it. 300mg/ml is definatly the limit, anything higher is gonna hurt like a bitch for days and probably hinder your workouts, hence hindering your growth, not to mention whatever else it might do.

 

[SouthernMuscle]

makes sense, but then why would it be just the test that hurts and not the eq?

and so should I just cut the test with some sterile oil?

 

[BigBoyJ]

Eq just isn't a painful injection like test. I would mix the test and eq. Put 1cc of each into the syringe and see how that works.

 

[SouthernMuscle]

I think that's what I'm gonna do, and see how the delts take it

now all I gott do is get rid of this damn swelling so I can go back to work tomorrow

 

[Nssca]

Come on IfBB Pros!!! Lets hear about Crystalization of the high Mg:ML ratio thats causing the pain...

 

[SouthernMuscle]

care to elaborate?

 

[Pittbull™]

Come on IfBB Pros!!! Lets hear about Crystalization of the high Mg:ML ratio thats causing the pain...

Yes please elaborate on this DaRooster, why does crystalisation of the high mg/ml gear cause pain & why is this happening in the test & not the eq?

Pittbull

 

[rAJJIN]

well the eq dosnt crystalize up Like test.
Its a liquid to begin with.

 

[massmonster32]

Well if it was me I would cut back on the mls per injection on the Test. You might try to mix 2.5 mls of Eq for every .5mls of that high mg test. But then you are gona have to take more injects to get enough Test per week. MM

 

[bigbadasian]

Reply

|---[\\\\]>----------- You just gotta cutt it. i mix my T400 (1/2cc) with 1.5cc's of s'thing else.

 

[Pittbull™]

well the eq dosnt crystalize up Like test.
Its a liquid to begin with.

Thanks bro, that makes sense now. What temp does it become liquid?

Pittbull

 

[SouthernMuscle]

thanks bros, ordering the sterile oil right now

 

[Ethan James]

Thanks bro, that makes sense now. What temp does it become liquid?

Pittbull

a really low temp... I think like 85-90 degrees

 

[rAJJIN]

eq?

Ive never seen the Eq (bold undecyclanate) in any form other then liquid.
winter, summer etc.

Now the test enan melting point is low as EJ said.
appx 85 degrees.

 

[Dave_19]

just buy some usp grade oil and dilute it 50:50 and stop just doing your glutes if they are sore, start atleast poking your shoulders as well.

 

[Nssca]

Yes please elaborate on this DaRooster, why does crystalisation of the high mg/ml gear cause pain & why is this happening in the test & not the eq?

Pittbull

Elaborating...
http://www.professionalmuscle.com/forums/showthread.php?t=1173&highlight=High+test+pain