• All new members please introduce your self here and welcome to the board:
    http://www.professionalmuscle.com/forums/showthread.php?t=259
Buy Needles And Syringes With No Prescription
M4B Store Banner
muscleshop
Riptropin Store banner
Generation X Bodybuilding Forum
Buy Needles And Syringes With No Prescription
Buy Needles And Syringes With No Prescription
Mysupps Store Banner
IP Gear Store Banner
PM-Ace-Labs
Ganabol Store Banner
Spend $100 and get bonus needles free at sterile syringes
Professional Muscle Store open now
DB-Banner
PHARMAHGH1
kinglab
ganabol2
Professional Muscle Store open now
over 5000 supplements on sale at professional muscle store
roids-210x65-48kb-1
granabolic1
napsgear-210x65
advertise1
over 5000 supplements on sale at professional muscle store
over 5000 supplements on sale at professional muscle store
over 5000 supplements on sale at professional muscle store
over 5000 supplements on sale at professional muscle store
over 5000 supplements on sale at professional muscle store
over 5000 supplements on sale at professional muscle store
over 5000 supplements on sale at professional muscle store
over 5000 supplements on sale at professional muscle store
over 5000 supplements on sale at professional muscle store
over 5000 supplements on sale at professional muscle store
over 5000 supplements on sale at professional muscle store
over 5000 supplements on sale at professional muscle store
over 5000 supplements on sale at professional muscle store

IP's prop/susp---CHUNKY??? WTF???

BStrongBwell

New member
Newbies
Joined
Jun 6, 2002
Messages
7
IP's prop/susp---CHUNKY??? WTF???
Anyone have this prob w/ IP's prop/susp blend where the susp is not fine like usual, but has big chunks in it?

>>>DOes anyone know of a way to get it to dissolve or break up through either heat or using BA or whatever????
 

xcelbeyond

The "Elder" Mod
Kilo Klub Member
Registered
Joined
Jun 5, 2002
Messages
7,226
I've experienced this with home-made gear. You can re-heat it (I assume it's in an oil base) either in boiling water or on "low" setting on an electric range (but be careful to no get too hot). Just swirl it around and "be patient." I had some winny that wouldn't suspend and I heated it as stated above so it would re-suspend so I could draw it out and put into caps. It took over 1/2 hour for it to completely dissolve.

The problem I've experienced "most" of the time is it separates out when it cools off. It could be because he didn't put in enough BA to keep it suspended :D j/k

xcel
 

haze324

FOUNDING Member
Registered
Joined
Jun 18, 2002
Messages
642
Heat

All you need is some heat man. I put in warm/hot water for while and swirled it around every few minutes and it completely dissovled into a light yellow solution. I filtered it, then put in it in the oven for about 20 min and got a clear final product. A few crystals have formed in the bottom every 4-5 days and I just throw it in the oven for a few minutes and it goes back to normal. That shit hurt the first couple of shots but after heating it a few times the pain is gone now. Good luck.
HZ
 

Staff online

  • A50#
    Old School Moderator
  • LATS
    Moderator / FOUNDING Member / NPC Judge

Forum statistics

Total page views
527,773,413
Threads
129,156
Messages
2,570,656
Members
157,883
Latest member
musclexxl
Phil Hernon Personal Training email
HGH Power Store email banner
Leader Powder Store email banner
Prowrist straps store banner
biogenix2
FLASHING-BOTTOM-BANNER-210x131
raws
Savage Labs Store email
Syntherol Site Enhancing Oil Synthol
AQ3 email Banner
pomps
rawhormone
ezgif-com-resize-2-1
MA Research Chem store banner
MA Supps Store Banner
Keytech banner
musclechem
Godbullraw-bottom-banner
Injection Instructions for beginners
Knight Labs store email banner
Top